|
|
| Tape Mirroring |
 |
High Performance |
|
Enhanced Reliability |
|
Disaster Recovery |
|
 |
|
|
|
|
When
One Copy Just Isn't Enough |
|
| Increased Overall System Performance
– Simultaneously
create two identical backup tapes in real-time. No
additional software overhead. |
|
| Increased Data Availability
– Recover valuable data even if one tape becomes lost, stolen or damaged.
|
|
|
|
Increased Reliability – Verify restored data automatically comparing tape
contents. Either copy can be used independently for recovery. |
|
| Disaster Recovery – Full fault tolerance
protection with user configurable disaster recovery options. |
|
| 100% Software Transparency –
No software changes of any kind are required. For
current systems using tape, the imager 2 is plug and play
with "ALL" existing tape backup software. |
|
| NT / Win 95 / 98 GUI –
A full featured GUI for controlling and monitoring all
operating and off-line modes. |
|
| Plug
Compatibility – The Imager 2 controller is
presented to the host as a single SCSI tape drive
providing plug and play with host systems supporting
SCSI-1 and SCSI-2 tape protocols. |
|
| Maximum Flexibility and
Control -
Four specific mirroring mode options, two disaster
recovery options, fault tolerant mode and two pass through
options. |
|
| Robotics
Support – compatible with existing autoloader
and library software in both striping and mirroring
modes of operation. |
|
| Offline Operations
– The Imager 2 controller has built in hardware
utilities for: Tape Copy, Tape Compare, Tape Verify, Tape
Drive Diagnostics and "Self Test" Diagnostics. |
|
|
|
|
| Supported RAID Levels |
| Level 1 |
Mirroring two drives |
|
|
| Host Interface |
| Low Voltage
Differential (LVD) - The host interface provides connection between
the Imager 2 mirroring controller and the SCSI host system.
It conforms to the SCSI-2 protocol while maintaining
compatibility to SCSI-1, 8/16 bit SCSI. Ultra synchronous
transfers combined with wide transfers allows for a
maximum of 40 MB/sec burst data rate. |
|
| Array Interface |
| Low Voltage
Differential (LVD) - The drive interface provides 2 parallel SCSI
channels between the Imager 2 mirroring controller and the
tape drives. The 8/16 bit SCSI fast ultra synchronous
transfers allow for a maximum of 40 MB/sec burst
data rate. Compatible with all SCSI-1 and SCSI-2 devices.
All major tape drives are supported. |
|
| GUI for NT / Win 95 / 98 |
| Ultera offers an optional remote access
Graphical User Interface program called
"Ultimate" that runs under NT, Win95, Win98 and
DOS. Running on the host system, Ultimate allows the
user to remotely control up to 8 Ultera Tape Array
subsystems. |
|
| Operator Console |
| The front panel operator console features a 4
line by 20 character display and 4 push button key pad. |
|
|
|
|
| TM051 |
|
Controller board only |
|
|
|
| TM851 |
|
5 1/4" Half
Height internal packaging with front panel operator console |
|
|
|
| TM1051 |
|
Table Top external
packaging with power supply and front panel operator console |
|
|
|
| TM2151 |
|
Single Controller
Board, 1U high 19 inch rackmount with power supply and front panel operator console |
|
|
|
| TM2251 |
|
Dual Controller
Boards,1U high 19 inch rackmount with 2 power supplies and 2 front panel operator consoles |
|
|
|
|
|
One Year Warranty |
|
|
|
|
|
|
| Board |
|
5.50" |
7.80" |
0.50" |
| 5 1/4" Half
Height |
|
5.75" |
9.20" |
1.67" |
| Low Profile Table
Top |
|
9.75" |
11.00" |
2.50" |
| Rackmount |
|
17.00" |
23.31" |
1.75" |
|
| Environment (Exclusive of Drives) |
|
| POWER |
| Input Voltage |
|
+5VDC,
10% |
| Supply Current |
|
2.0
amps, max |
|
|
|
| TEMPERATURE |
|
|
| Operating |
|
5
degree C to 50 degree C |
| Non-operating |
|
-40
degree C to 60 degree C |
|
|
|
| HUMIDITY |
|
|
| Operating |
|
10% to
80% non-condensing |
| Non-operating |
|
10% to
90% non-condensing |
|
|
| Also
Available As:
|
|
|
Library Master
Specifications
|
RAIL
Master Specifications
|
|
|
|
|
LibraryMaster™
Models
|
|
|
|
| TL051 |
|
Controller board only |
|
|
|
| TL851 |
|
5 1/4" Half
Height internal packaging with front panel operator console
|
|
|
|
| TL1051 |
|
Table Top external
packaging with power supply and front panel operator console |
|
|
|
| TL2151 |
|
Single Controller
Board, 1U high 19 inch rackmount with power supply and front panel operator console
|
|
|
|
| TL2251 |
|
Dual Controller
Boards,1U high 19 inch rackmount with 2 power supplies and 2 front panel operator consoles |
|
|
RAILMaster™
Models
|
|
|
|
| TR051 |
|
Controller board only |
|
|
|
| TR851 |
|
5 1/4" Half
Height internal packaging with front panel operator console
|
|
|
|
| TR1051 |
|
Table Top external
packaging with power supply and front panel operator console |
|
|
|
| TR2151 |
|
Single Controller
Board, 1U high 19 inch rackmount with power supply and front panel operator console
|
|
|
|
| TR2251 |
|
Dual Controller
Boards,1U high 19 inch rackmount with 2 power supplies and 2 front panel operator consoles |
|
|
|
|
 |
 |
 |
5
1/4" Internal
Half Height |
Low
Profile
Table Top |
Rackmount |
|
|
 |
Ultera Systems, Inc.
26052 Merit Circle · Laguna Hills, CA 92653
Phone: 949.367.8800 · Fax: 949.367.0758
E-mail: inform@ultera.com
Visit us at www.ultera.com |
|
